Universal Chassis-40mm Steer (INL,Multi,Sphl bush)
Made by
Print With Shapeways
Choose Your Material
Choose your color and finish
Choose Your Material
$29.00
Choose your color and finish
Have a question about this product?
contact the designerYou must be logged in and verified to contact the designer.
Product Description
Universal Chassis-40mm Steer (INL,Multi,Sphl bush)
- Rear uses spherical bushes (Slot It CH56b), see video click here.
- Inline config
- Takes the slim can motor (Shaft lengths 8, 10 & 14mm)
- Takes the S-Can motor, endbell drive.
- Takes the Boxer / Flat motor.
- Takes the short can motor with 8mm shaft.
- Takes the short can motor with 12mm shaft.
- Chassis rear width 24mm.
- Rear ride height adjustment of 1.5mm, using M2 grub screws.
- Wheelbase 95mm (max) & 62mm (min) after trimming.
- Screws needed: M2.2 screws for Body posts & fixing nuts. M2 grub screws for ride height adjustment & mounting motor brackets.
- Slim can motor’s use motor brackets 1 & 2.
- Motor bracket #1 used for front of motor & bracket #2 used for rear of motor.
- Slim motor with 8mm shaft uses holes 2 & 5.
- Slim motor with 10mm shaft uses holes 3 & 6.
- Slim motor with 14mm shaft uses holes 4 & 7.
- Boxer/Flat motor’s use motor brackets 3 & 4.
- Motor bracket #3 used for front of motor & bracket #4 used for rear of motor.
- Boxer/Flat motor brackets use holes 1 & 5.
- 12mm Shaft Short Can motor uses motor brackets 3 & 5.
- Motor bracket #3 used for front of motor & bracket #5 used for rear of motor.
- 12mm Shaft Short Can motor brackets use holes 3 & 7.
- 8mm Shaft Short Can motor uses motor brackets 3 & 4.
- Motor bracket #3 used for front of motor & bracket #4 used for rear of motor.
- 8mm Shaft Short Can motor brackets use holes 1 & 5.
- S-Can motor uses motor brackets 6 & 7.
- Motor bracket #6 used for front of motor & bracket #7 used for rear of motor.
- S-Can motor bracket #6 uses holes 1 & 2.
- S-Can motor bracket #7 uses holes 6 & 7.
- Screw set needed for front end assembly, available in the “Parts - JA Slots” section,
click here. (Parts include: 3x M2.2x12mm Screws, 2x M2.2x6mm Screws, 2x 12.5mm Stub Axles(3/32) in Steel, S/S or PA12).
- Washers can be assembled above or below the hubs for some height adjustment.
- Motor wire fixing under the front axle.
- Some trimming may be needed due to the nature of 3D printing.
Parts Included:
1x Front Steering End
1x Left & Right hubs
1x Bracket Arm
1x Guide
2x 1mm Washers
1x Rear End
2x Fixing Nuts
2x Body Posts
General Material Notes:
Colors are slightly more flexible then Black, White is slightly more flexible then colors.
(Ref: JA100)
- Rear uses spherical bushes (Slot It CH56b), see video click here.
- Inline config
- Takes the slim can motor (Shaft lengths 8, 10 & 14mm)
- Takes the S-Can motor, endbell drive.
- Takes the Boxer / Flat motor.
- Takes the short can motor with 8mm shaft.
- Takes the short can motor with 12mm shaft.
- Chassis rear width 24mm.
- Rear ride height adjustment of 1.5mm, using M2 grub screws.
- Wheelbase 95mm (max) & 62mm (min) after trimming.
- Screws needed: M2.2 screws for Body posts & fixing nuts. M2 grub screws for ride height adjustment & mounting motor brackets.
- Slim can motor’s use motor brackets 1 & 2.
- Motor bracket #1 used for front of motor & bracket #2 used for rear of motor.
- Slim motor with 8mm shaft uses holes 2 & 5.
- Slim motor with 10mm shaft uses holes 3 & 6.
- Slim motor with 14mm shaft uses holes 4 & 7.
- Boxer/Flat motor’s use motor brackets 3 & 4.
- Motor bracket #3 used for front of motor & bracket #4 used for rear of motor.
- Boxer/Flat motor brackets use holes 1 & 5.
- 12mm Shaft Short Can motor uses motor brackets 3 & 5.
- Motor bracket #3 used for front of motor & bracket #5 used for rear of motor.
- 12mm Shaft Short Can motor brackets use holes 3 & 7.
- 8mm Shaft Short Can motor uses motor brackets 3 & 4.
- Motor bracket #3 used for front of motor & bracket #4 used for rear of motor.
- 8mm Shaft Short Can motor brackets use holes 1 & 5.
- S-Can motor uses motor brackets 6 & 7.
- Motor bracket #6 used for front of motor & bracket #7 used for rear of motor.
- S-Can motor bracket #6 uses holes 1 & 2.
- S-Can motor bracket #7 uses holes 6 & 7.
- Screw set needed for front end assembly, available in the “Parts - JA Slots” section,
click here. (Parts include: 3x M2.2x12mm Screws, 2x M2.2x6mm Screws, 2x 12.5mm Stub Axles(3/32) in Steel, S/S or PA12).
- Washers can be assembled above or below the hubs for some height adjustment.
- Motor wire fixing under the front axle.
- Some trimming may be needed due to the nature of 3D printing.
Parts Included:
1x Front Steering End
1x Left & Right hubs
1x Bracket Arm
1x Guide
2x 1mm Washers
1x Rear End
2x Fixing Nuts
2x Body Posts
General Material Notes:
Colors are slightly more flexible then Black, White is slightly more flexible then colors.
(Ref: JA100)
Details
What's in the box:
SPW-Uni-Inl_MM-SB-Chassis-40mm-St-Front
Dimensions:
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
