Black Natural Versatile Plastic
Oxy2 Antenna Guide
Made by
Print With Shapeways
Choose Your Material
Choose your color and finish
Choose Your Material
$13.00
Choose your color and finish
Have a question about this product?
contact the designerYou must be logged in and verified to contact the designer.
Product Description
Description
Securely snaps in place on your Oxy 2 tailboom between the boom clamp and front tail servo mount to route antennas away from the fuselage and at 90 degrees to each other. This is especially useful when mounting small receivers on the bottom of the boom clamp.
The antenna guides are carefully designed to avoid interference with the tail servo arm, and standard 1/8" (0.125") O.D. antenna tubes (not included) can be press-fit in the guides to keep antenna coax straight. Many coffee stirrers are perfectly sized for this.
Compatibility
Compatible with all Oxy 2 variants including 190 FE, 190 Sport, and 210 FE. Requires a minimum of 7mm clearance between the boom clamp and the forward tail servo mount (the 190 FE manual calls for 7.2mm clearance, and your clearance may be greater in practice, depending on your setup).
Technical Specifications
Width: 30.9 mm
Height: 29.4 mm
Depth: 15.9 mm
Weight: 1.02 g
Installation
The 3D printing process sometimes leaves excess powder in the individual antenna guides - gently remove it with a toothpick or similar implement. Also, test-fit a 1/8" (0.125") O.D. coffee stirrer or antenna tube by pressing it into each guide. If the fit is too tight, try lightly reaming the guide by hand with a 7/64" drill bit.
Then, clip the guide onto your Oxy 2 tailboom, between the boom clamp and the front tail servo mount. This is easiest before you attach the tail servo, but it can be done with some patience even if the servo is already mounted. No glue is necessary, but a dab of silicone seal makes a good, reversible adhesive if you prefer. Then, feed your receiver antennas through the antenna guides on the clamp, and press-fit 1/8" (0.125") O.D. coffee stirrers or antenna tubes.
If you're adding the antenna guide to an existing Oxy 2, it is easiest if you feed your receiver antennas partway through the guides on the clamp before sliding it between the servo and boom clamp, onto the boom.
NOTE: antenna tubing not included.
Securely snaps in place on your Oxy 2 tailboom between the boom clamp and front tail servo mount to route antennas away from the fuselage and at 90 degrees to each other. This is especially useful when mounting small receivers on the bottom of the boom clamp.
The antenna guides are carefully designed to avoid interference with the tail servo arm, and standard 1/8" (0.125") O.D. antenna tubes (not included) can be press-fit in the guides to keep antenna coax straight. Many coffee stirrers are perfectly sized for this.
Compatibility
Compatible with all Oxy 2 variants including 190 FE, 190 Sport, and 210 FE. Requires a minimum of 7mm clearance between the boom clamp and the forward tail servo mount (the 190 FE manual calls for 7.2mm clearance, and your clearance may be greater in practice, depending on your setup).
Technical Specifications
Width: 30.9 mm
Height: 29.4 mm
Depth: 15.9 mm
Weight: 1.02 g
Installation
The 3D printing process sometimes leaves excess powder in the individual antenna guides - gently remove it with a toothpick or similar implement. Also, test-fit a 1/8" (0.125") O.D. coffee stirrer or antenna tube by pressing it into each guide. If the fit is too tight, try lightly reaming the guide by hand with a 7/64" drill bit.
Then, clip the guide onto your Oxy 2 tailboom, between the boom clamp and the front tail servo mount. This is easiest before you attach the tail servo, but it can be done with some patience even if the servo is already mounted. No glue is necessary, but a dab of silicone seal makes a good, reversible adhesive if you prefer. Then, feed your receiver antennas through the antenna guides on the clamp, and press-fit 1/8" (0.125") O.D. coffee stirrers or antenna tubes.
If you're adding the antenna guide to an existing Oxy 2, it is easiest if you feed your receiver antennas partway through the guides on the clamp before sliding it between the servo and boom clamp, onto the boom.
NOTE: antenna tubing not included.
Details
What's in the box:
Oxy2 Antenna Guide
Dimensions:
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
